top of page
2D150-500

2D150-500

SKU: 2D150-500

Operation: 2D150-500 Series 2/2 Pilot Operated Diaphragm Solenoid Valve NC

 

To open: when the valve receives an electrical signal, a magnetic field is formed which attracts the plunger covering the pilot orifice to lift off, causing system pressure (holding the diaphragm/piston closed) to drop. As system pressure on the top of the diaphragm/piston is reduced, full system pressure on the other side of the diaphragm/ piston acts to lift the diaphragm/piston away from the main orifice, which allows media flow through the valve. Since the bleed orifice is dimensionally smaller than the pilot orifice, the system pressure can t rebuild on the top of the diaphragm/piston as long as the pilot orifice remains open.

 

To close: when the valve is de-energized, it releases its hold on the plunger. Then the plunger drops and covers the main orifice. The system pressure builds up on the top of the diaphragm/piston through the bleed orifice, forcing the diaphragm/piston down until it covers the main orifice and stops media flow through the valve.

 

Safety Note: Standard valves are supplied with continuous duty coils. The proper class of insulation for the service is indicated on the coil. The coil temperature may become hot after being energized for extended periods, but it is normal. Do not energize the coil without installing it onto the valve or connect the coil to a wrong voltage, as it may overheat and damage the coil; although the coil is made of flame retarded material, misuse of the coil in this manner could create fire hazards and generate smoke or burning odor which indicates excessive coil temperature and should disconnect the power to the coil immediately.

 

Download PDF

  • Product Specifications

    Brass Model 2D150-1/2 2D200-3/4 2D250-1 2D320-1 1/4 2D400-1 1/2 2D500-2
    Stainless Steel Mode 2DS150-1/2 2DS200-3/4 2DS250-1 2DS320-1 1/4 2DS400-1 1/2 2DS500-2
    Port Size 1/2” NPT 3/4” NPT 1” NPT 1 1/4” NPT 1 1/2” NPT 2” NPT
    Orifice 15mm 20mm 25mm 32mm 40mm 50mm
    Flow Coefficient (Cv) 3.7 7 11.1 14 24.5 35
    Valve Type 2 Way, Normally Closed (NC) 2 Way, Normally Closed (NC) 2 Way, Normally Closed (NC) 2 Way, Normally Closed (NC) 2 Way, Normally Closed (NC) 2 Way, Normally Closed (NC)
    Action Anti-Hammering, Slow Closing, Pilot Diaphragm Anti-Hammering, Slow Closing, Pilot Diaphragm Anti-Hammering, Slow Closing, Pilot Diaphragm Anti-Hammering, Slow Closing, Pilot Diaphragm Anti-Hammering, Slow Closing, Pilot Diaphragm Anti-Hammering, Slow Closing, Pilot Diaphragm
    Wetted Surfaces

    2D Series Valve Body: Brass

    Standard 2DS Series Valve Body: 304 Stainless Steel

    Upgraded 2DS Series Valve Body: 316 Stainless Steel

    Seal: NBR (Buna N), or Viton (FKM)

    Armature Assembly: Stainless Steel

    2D Series Valve Body: Brass

    Standard 2DS Series Valve Body: 304 Stainless Steel

    Upgraded 2DS Series Valve Body: 316 Stainless Steel

    Seal: NBR (Buna N), or Viton (FKM)

    Armature Assembly: Stainless Steel

    2D Series Valve Body: Brass

    Standard 2DS Series Valve Body: 304 Stainless Steel

    Upgraded 2DS Series Valve Body: 316 Stainless Steel

    Seal: NBR (Buna N), or Viton (FKM)

    Armature Assembly: Stainless Steel

    2D Series Valve Body: Brass

    Standard 2DS Series Valve Body: 304 Stainless Steel

    Upgraded 2DS Series Valve Body: 316 Stainless Steel

    Seal: NBR (Buna N), or Viton (FKM)

    Armature Assembly: Stainless Steel

    2D Series Valve Body: Brass

    Standard 2DS Series Valve Body: 304 Stainless Steel

    Upgraded 2DS Series Valve Body: 316 Stainless Steel

    Seal: NBR (Buna N), or Viton (FKM)

    Armature Assembly: Stainless Steel

    2D Series Valve Body: Brass

    Standard 2DS Series Valve Body: 304 Stainless Steel

    Upgraded 2DS Series Valve Body: 316 Stainless Steel

    Seal: NBR (Buna N), or Viton (FKM)

    Armature Assembly: Stainless Steel

    Seal Material

    Standard Option: NBR (Buna N)

    Upgrade Option: Viton (FKM), EPDM

    Standard Option: NBR (Buna N)

    Upgrade Option: Viton (FKM), EPDM

    Standard Option: NBR (Buna N)

    Upgrade Option: Viton (FKM), EPDM

    Standard Option: NBR (Buna N)

    Upgrade Option: Viton (FKM), EPDM

    Standard Option: NBR (Buna N)

    Upgrade Option: Viton (FKM), EPDM

    Standard Option: NBR (Buna N)

    Upgrade Option: Viton (FKM), EPDM

    Operating Temperature

    Media with NBR Seal: 14°F to 176°F (-10°C to 80°C)

    Media with Viton Seal: 14°F to 266°F (-10°C to 130°C)

    Ambient: 23°F to 110°F (-5°C to 43°C)

    Media with NBR Seal: 14°F to 176°F (-10°C to 80°C)

    Media with Viton Seal: 14°F to 266°F (-10°C to 130°C)

    Ambient: 23°F to 110°F (-5°C to 43°C)

    Media with NBR Seal: 14°F to 176°F (-10°C to 80°C)

    Media with Viton Seal: 14°F to 266°F (-10°C to 130°C)

    Ambient: 23°F to 110°F (-5°C to 43°C)

    Media with NBR Seal: 14°F to 176°F (-10°C to 80°C)

    Media with Viton Seal: 14°F to 266°F (-10°C to 130°C)

    Ambient: 23°F to 110°F (-5°C to 43°C)

    Media with NBR Seal: 14°F to 176°F (-10°C to 80°C)

    Media with Viton Seal: 14°F to 266°F (-10°C to 130°C)

    Ambient: 23°F to 110°F (-5°C to 43°C)

    Media with NBR Seal: 14°F to 176°F (-10°C to 80°C)

    Media with Viton Seal: 14°F to 266°F (-10°C to 130°C)

    Ambient: 23°F to 110°F (-5°C to 43°C)

    Operating Pressure

    AC Coil: 4 PSI to 175 PSI

    DC Coil: 4 PSI to 145 PSI

    AC Coil: 4 PSI to 175 PSI

    DC Coil: 4 PSI to 145 PSI

    AC Coil: 4 PSI to 175 PSI

    DC Coil: 4 PSI to 145 PSI

    AC Coil: 4 PSI to 175 PSI

    DC Coil: 4 PSI to 145 PSI

    AC Coil: 4 PSI to 175 PSI

    DC Coil: 4 PSI to 145 PSI

    AC Coil: 4 PSI to 175 PSI

    DC Coil: 4 PSI to 145 PSI

    Electrical Connections

    D: DIN 43650, Form A (2W200C)

    ATEX: ATEX Explosion Proof Coil (2W200C-ATEX)

    D: DIN 43650, Form A (2W200C)

    ATEX: ATEX Explosion Proof Coil (2W200C-ATEX)

    D: DIN 43650, Form A (2W200C)

    ATEX: ATEX Explosion Proof Coil (2W200C-ATEX)

    D: DIN 43650, Form A (2W200C)

    ATEX: ATEX Explosion Proof Coil (2W200C-ATEX)

    D: DIN 43650, Form A (2W200C)

    ATEX: ATEX Explosion Proof Coil (2W200C-ATEX)

    D: DIN 43650, Form A (2W200C)

    ATEX: ATEX Explosion Proof Coil (2W200C-ATEX)

    Coil Power

    AC Coil: 28VA

    DC Coil: 12-20W

    AC Coil: 28VA

    DC Coil: 12-20W

    AC Coil: 28VA

    DC Coil: 12-20W

    AC Coil: 28VA

    DC Coil: 12-20W

    AC Coil: 28VA

    DC Coil: 12-20W

    AC Coil: 28VA

    DC Coil: 12-20W

    Coil Duty 100% ED (Continuous Duty) 100% ED (Continuous Duty) 100% ED (Continuous Duty) 100% ED (Continuous Duty) 100% ED (Continuous Duty) 100% ED (Continuous Duty)
    Voltage Options 12VDC, 24VDC, 24VAC, 110/120VAC (50/60Hz), 220/240VAC (50/60Hz) 12VDC, 24VDC, 24VAC, 110/120VAC (50/60Hz), 220/240VAC (50/60Hz) 12VDC, 24VDC, 24VAC, 110/120VAC (50/60Hz), 220/240VAC (50/60Hz) 12VDC, 24VDC, 24VAC, 110/120VAC (50/60Hz), 220/240VAC (50/60Hz) 12VDC, 24VDC, 24VAC, 110/120VAC (50/60Hz), 220/240VAC (50/60Hz) 12VDC, 24VDC, 24VAC, 110/120VAC (50/60Hz), 220/240VAC (50/60Hz)
    Voltage Tolerance ±10% of Specified Voltage ±10% of Specified Voltage ±10% of Specified Voltage ±10% of Specified Voltage ±10% of Specified Voltage ±10% of Specified Voltage
    Ingress Protection IP65 IP65 IP65 IP65 IP65 IP65
    Insulation Class H Class H Class H Class H Class H Class H Class
    Installation No Orientation Requirement No Orientation Requirement No Orientation Requirement No Orientation Requirement No Orientation Requirement No Orientation Requirement
    Service Liquid, Water, Oil, Air Liquid, Water, Oil, Air Liquid, Water, Oil, Air Liquid, Water, Oil, Air Liquid, Water, Oil, Air Liquid, Water, Oil, Air
  • Installation Instructions

    To connect the valve Inlet and Outlet:

    Connect the inlet and outlet in the direction of the arrow marked on the valve.

     

    To install coil:

    Put the coil onto the armature tube of the valve. Put the lock washer and nut onto the armature tube. Hand tighten the nut, then use a wrench to tighten the nut to a quarter turn; do not over-tighten the nut, it may cause the armature tube to fail prematurely.

     

    To connect DIN coil:

    1. Remove the Philip screw from the plastic housing and unplug it from the DIN coil.

    2. From the screw opening, push the terminal block out from the plastic housing.

    3. Note the 1, 2 and ground markings on underside of DIN enclosure.

    4. For DC DIN Coil, Connect 1 to Positive, 2 to Negative.

    5. For AC DIN Coil, connect 1 to HOT wire, 2 to Neutral wire, and if required connect.

    Do not energize the coil without installing it onto the valve, it will burn the coil and create fire hazards.

bottom of page